Alum foil tape
Solvent rubber adhesive series
Product Guide |
||
Product |
Description |
Application |
WAF3035 |
A nominal 30 micron (1.2 mil) high tensile strength aluminum foil backing, combined with a high performance synthetic rubber-resin adhesive, protected by an easy-release silicone release paper. |
HVAC industry for joining and sealing Foil-Scrim-Kraft Facing laminated fiberglass blanket / duct board joints and seams; joining and sealing flexible air duct seams and connections. May also be used for other industrial uses requiring a tape with these characteristics and benefits. |
WAF4035 |
A nominal 40 micron (1.6 mil) dead soft aluminum foil backing, combined with a high performance solvent synthetic rubber-resin adhesive, protected by an easy-release silicone release paper. |
HVAC industry for joining and sealing Foil-Scrim-Kraft Facing laminated fiberglass blanket / duct board joints and seams; joining and sealing flexible air duct seams and connections. May also be used for other industrial uses requiring a tape with these characteristics and benefits. |
WAF5035 |
A nominal 50 micron (2.0 mil) high tensile strength aluminum foil backing, combined with a high performance solvent synthetic rubber-resin adhesive, protected by an easy-release silicone release paper. |
HVAC industry for joining and sealing Foil-Scrim-Kraft Facing laminated fiberglass blanket / duct board joints and seams; joining and sealing flexible air duct seams and connections. May also be used for other industrial uses requiring a tape with these characteristics and benefits. |
WAF7135A |
3-way Foil-Scrim-Kraft backing, combined with a transparent high performance solvent synthetic rubber-resin adhesive, protected by an easy-release silicone release paper. |
HVAC industry for joining and sealing Foil-Scrim-Kraft Facing laminated fiberglass blanket / duct board joints and seams; joining and sealing flexible air duct seams and connections. May also be used for other industrial uses requiring a tape with these characteristics and benefits. |
WFS1835B |
Foil-Scrim backing (Foil: 18u / 2-way Scrim: 5x5mm), combined with high performance solvent rubber-resin adhesive, protected by an easy-release silicone release paper. |
HVAC industry for joining and sealing Foil-Scrim Facing laminated fiberglass blanket / duct board / pipe section joints and seams; joining and sealing flexible air duct seams and |
Typical Physical Properties |
|||||||
Product |
Backing |
Adhesive |
Thickness mm |
Adhesion N/25mm |
Tensile N/25mm |
Elongation % |
Service Temp¡ãC |
WAF3035 |
Foil 30u |
Rubber-Resin |
70 |
30 |
45 |
3 |
-20 ~ +80 |
WAF4035 |
Foil 40u |
Rubber-Resin |
80 |
30 |
55 |
3 |
-20 ~ +80 |
WAF5035 |
Foil 50u |
Rubber-Resin |
90 |
30 |
75 |
3.5 |
-20 ~ +80 |
WAF7135A |
3-way FSK |
Rubber-Resin |
170 |
30 |
120 |
1 |
-20 ~ +80 |
WFS1835B |
Foil-Scrim |
Rubber-Resin |
83 |
30 |
100 |
3 |
-20 ~ +80 |
PRODUCT FORM & SIZE AVAILABLE
Cut Roll: 48 / 50mm (2") / 60 / 63mm (2.5") / 72 / 75mm (3") / 96mm / 100mm (4")
Log Roll: 1200mm x 45 / 50m Jumbo Roll: 1200mm x 750m / 800m
IMPORTANT NOTE
1. The data above are typical values only, and should not be used for specifications purpose.
2. Tolerance: Weight and Thickness: ¡À10%; Width: ¡À3mm; Length: Cut Roll: ¡À0.3m, Jumbo Roll ¡À0.5%.
STORAGE & SHELF LIFE: 12 months when stored at 21¡ãC (70¡ãF) / 50% relative humidity out of direct sunlight.
SURFACE PREPARATION: It is essential, as with all pressure-sensitive tapes, that the surface to which the tape is applied must be clean, dry, free of grease, oil or other contaminants.
PRODUCT USE: It is essential that the user evaluate the TEXAL product to determine whether it is fit for a particular purpose and user¡¯s method of application. Good results will be obtained when applied to a clean, dry surface with a suitable pressure on TEXAL products between +10 ~ +40¡ãC (+50 ~ +105 ¡ãF).